Products

Products of GE

  • GE 489 l Generator Protection System
    GE 489 l Generator Protection System

    The SR489 Generator Protection System, a member of the SR family of relays, provides protection, control and advanced communications in a cost effective industry leading draw-out construction. Designed for small and medium sized generators, the 489 delivers advanced protection including generator stator differential protection. The 489 also includes detailed diagnostic information allowing for reduced troubleshooting time.

    View More
  • GE G30 |  Generator Protection System
    GE G30 | Generator Protection System

    Protection for small to medium generators, combined generators and transformers Built on the industry-leading UR platform, the G30 provides advanced protection for small to medium-sized steam, hydraulic and combustion-turbine generators. The G30 is also well suited for applications where both the generator and transformer are in the same zone of protection, providing the required protection in one device. The G30 provides advanced communication with an integrated managed Ethernet switch, while supporting standard communication protocols including IEC 61850.

    View More
  • GE G650 | Generator Protection and Control System
    GE G650 | Generator Protection and Control System

    The G650 is a Distributed Generation Protection and Control Relay designed for complete protection of small to medium sized generators as well as operate as a control system for distributed generation interconnections. The G650 provides a cost effective and scalable solution that allows for tailoring your protection, communications, and I/O requirements to meet the needs of your specific application.

    View More
  • GE GPM-S | Stator Ground Protection Module
    GE GPM-S | Stator Ground Protection Module

    Stator ground module works in combination with UR G60 to provide a 100% stator ground fault protection that is operational during generator start-up, running and stopped conditions. In the 100% stator ground fault protection based on sub-harmonic injection, a 20Hz voltage is injected to detect ground faults at any point across 100% of the winding thereby protecting the complete stator winding and allowing early detection of stator ground fault conditions.

    View More
  • 889 Generator Protection System
    889 Generator Protection System

    Primary or backup protection for generators Suitable for combined generator and in-zone transformer differential protection Support for a wide range of communications protocols, network architectures, and time synchronization, including Modbus, DNP 3.0, IEC 61850 Edition 2, and IEEE 1588 Time Sync

    View More
  • GE G60 | Generator Protection System
    GE G60 | Generator Protection System

    Comprehensive protection for AC generators. The G60 Generator Protection System, a member of the UR Family of protection relays, provides protection for AC generators. It may be used on any size of generator driven by steam, gas, hydraulic or other turbines.

    View More
  • P348 - Variable Speed Double Fed Induction Machine Protection IED
    P348 - Variable Speed Double Fed Induction Machine Protection IED

    Advanced variable speed generator management relay Process bus inputs for connection to non-conventional CTs Low frequency protection of the rotor and stator from 0.1-70Hz

    View More
  • P391 Rotor Earth Fault Module
    P391 Rotor Earth Fault Module

    Detects rotor earth fault faults in the field winding of the generator. Requires the P34x relay to have the current loop CLIO hardware option fitted. Used with P342, P343, P344, P345 and P346 Generator protection relays

    View More
  • W650 Wind Generator Protection System
    W650 Wind Generator Protection System

    Advanced wind turbine protection and control system. W650 Generator Protection System, a member of the 650 Family of protection relays, is a machine controller management device.

    View More
  • GE GPM-F | Field Ground Protection Module
    GE GPM-F | Field Ground Protection Module

    The field ground protection module, GPM-F works in combination with the Multilin G60 to detect ground faults in the field winding of the generator. Providing application flexibility, the field ground protection module can be configured for either single point injection or double point injection based on application requirements. The solution includes: two stage field ground detection, injected voltage and current supervision, brush lift-off detection, field over and under current elements and field ground fault location.

    View More
  • P345 Large Generator Management Relay with Stator Earth Fault
    P345 Large Generator Management Relay with Stator Earth Fault

    Advanced generator management relay with low frequency injection 100% stator earth fault for large generators Comprehensive generator and transformer protection and condition monitoring Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • P344 Generator Management Relay with 2 Neutral Voltage Inputs
    P344 Generator Management Relay with 2 Neutral Voltage Inputs

    Advanced generator management relay with 2 neutral voltage inputs for medium/large generators Comprehensive generator and transformer protection and condition monitoring Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • P14DG Distributed Generator Interconnection Relay
    P14DG Distributed Generator Interconnection Relay

    Directional Feeder Management relay for small generator protection Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Check sync and voltage restrained overcurrent protection and power function included

    View More
  • P341 Interconnection Protection Relay
    P341 Interconnection Protection Relay

    Comprehensive protection for interconnecting distributed resources with the electric power system Provides Dynamic Line Rating (DLR) for transmission line capacity optimization Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • P342 Small Generator Management IED
    P342 Small Generator Management IED

    Advanced generator management relay for small generators Programmable curves for easy protection customisation Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • P343 Medium to Large Sized Generator Management IED
    P343 Medium to Large Sized Generator Management IED

    Advanced generator management relay for medium/large generators Comprehensive generator and transformer protection and condition monitoring Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • Modem and Accessories
    Modem and Accessories

    Two high output power BPL port with integrated 4-port switch with AC and DC power supply Long range version for extra distance coverage without repeaters Coupler and accessories

    View More
  • S20 Managed Ethernet Switch
    S20 Managed Ethernet Switch

    Fully flexible layer 2 & 3 Ethernet switch for industrial applications, including PRP redundant networks. Allows up to 24 ports with speeds of up to 1 Gbps, as required in high-end process bus applications. Sub-microsecond accurate time synchronization using IEEE 1588v2 PTP. Modular design, interfaces can be hot-swapped without reconfiguration. Redundant power supply.

    View More
  • Intermediate Arrester
    Intermediate Arrester

    Designed and tested in accordance with the ANSI/IEEE C62.11 and IEC 99-4 standards. Available in rated voltage up to 144 kV. Suitable for both indoor and outdoor applications.

    View More
  • Station Arrester
    Station Arrester

    Designed and tested in accordance with the ANSI/IEEE C62.11. Available in rated voltages up to 612 kV in porcelain housings. Suitable for both indoor and outdoor applications.

    View More
  • Riser Pole Arrester
    Riser Pole Arrester

    Suitable for both indoor and outdoor applications. Designed and tested in accordance with the latest revision of ANSI/IEEE C62.11 and IEC 9-4.

    View More
  • Surge Protective Device
    Surge Protective Device

    Suitable for indoor applications. Design and tested with the 4th edition of UL1449

    View More
  • GE 345 | Transformer Protection System
    GE 345 | Transformer Protection System

    The 345 is a microprocessor-based system for primary and backup protection of low and medium voltage power transformers. The 345 offers advanced algorithms for automatic magnitude and phase compensations for more than twenty types of two winding transformers, fast and secure biased differential protection with dual slope, dual breakpoint characteristic.

    View More
  • GE 745 | Transformer Protection System
    GE 745 | Transformer Protection System

    The 745 Transformer Protection System is a full featured transformer protection relay, suitable for application on small, medium, and large power transformers. The 745 can be applied on two-winding and three-winding transformers. Uses multiple current and voltage inputs to provide primary protection and back-up protection of transformers, including differential, ground differential phase, neutral, and ground overcurrent, over-fluxing, and on-load tap changer.

    View More
  • GE T35 | Transformer Protection System
    GE T35 | Transformer Protection System

    Cost-effective differential protection for transformers with up to 6 sets of CTs The T35 is designed to provide basic transformer protection functions for variety of transformer applications. It uses multiple current inputs to provide primary protection and backup protection of transformers, including differential, phase and ground overcurrent. The relay can be configured to accept up to 6 sets of current inputs to provide proper differential restraint for applications with three-winding transformers with windings configured in dual-breaker arrangements.

    View More
  • GE T60 | Transformer Protection System
    GE T60 | Transformer Protection System

    The T60 is designed for various power applications, including autotransformers, generator step-up transformers, split-phase, angle regulating transformers and reactors. It uses multiple current and voltage inputs to provide primary protection and backup protection of transformers, including differential, ground differential, five distance zones, phase, neutral, and ground overcurrent, under and overvoltage, under and overfrequency, over-fluxing, and breaker failure.

    View More
  • P652 - 2 Winding Transformer Management Relay
    P652 - 2 Winding Transformer Management Relay

    Protection for 2 winding applications High-speed differential, inrush restraint, REF (high or low impedance modes), thermal overload, backup overcurrent / earth fault protection (HV and LV) Supervision including measurement, monitoring and recording functions Serial communication protocols (Modbus, IEC60870-5-103, DNP3.0)

    View More
  • P645 - 5 End Transformer Management Relay
    P645 - 5 End Transformer Management Relay

    Comprehensive protection for 2 or 3 winding transformers, with dual breaker feeding on up to two sides High and low impedance restricted earth fault (REF), Fast reset (less than 1 cycle) circuit breaker failure element Integral asset management capability: transformer thermal overload (IEEE Standard C57.91), loss of life (LOL) and through fault monitoring Compact 40TE Digital Substation version supporting IEC61850-9-2 LE and IEC61850-8-1 Ed 2

    View More
  • P642 - 2 Winding Transformer Management Relay
    P642 - 2 Winding Transformer Management Relay

    Comprehensive suite of main and back-up protection for 2 winding applications High and low impedance restricted earth fault (REF), Fast reset (less than 1 cycle) circuit breaker failure element Integral asset management capability: transformer thermal overload (IEEE Standard C57.91), loss of life (LOL) and through fault monitoring IEC 61850/DNP 3.0 redundant Ethernet, supporting self-healing ring, RSTP, dual homing, PRP or HSR

    View More
  • P643 - 3 End Transformer Management Relay
    P643 - 3 End Transformer Management Relay

    Comprehensive protection for 3 winding transformers, or 2 winding with dual breaker feeding on one side High and low impedance restricted earth fault (REF), Fast reset (less than 1 cycle) circuit breaker failure element Integral asset management capability: transformer thermal overload (IEEE Standard C57.91), loss of life (LOL) and through fault monitoring IEC 61850/DNP 3.0 redundant Ethernet, supporting self-healing ring, RSTP, dual homing, PRP or HSR

    View More
  • 845 Transformer Protection System
    845 Transformer Protection System

    High-speed draw-out multiprocessor-based relay for transformer protection and management. Intended for the primary protection and management of small, medium and large power transformers. Comprehensive transformer health monitoring, diagnostics and reporting with integrated connectivity to single and multi-gas transformer DGA solutions.

    View More
  • KVGC Voltage Regulating Control Relay
    KVGC Voltage Regulating Control Relay

    Compact multifunction numerical relay. Continually monitors system voltage. Suitable for parallel transformer applications. Increased equipment lifetimes.

    View More
  • Cable Connectors
    Cable Connectors

    High strength, corrosion proof aluminium alloy connectors for applications up to 420 kV Easy and safe assembly Meets international standards Optional copper plated aluminum lining Customized dimensions available

    View More
  • Palm Cable Connectors
    Palm Cable Connectors

    High strength, corrosion proof aluminium alloy connectors for applications up to 420 kV Easy and safe assembly Meets international standards Optional copper plated aluminum lining Customized dimensions available

    View More
  • Protective Capacitor-AC Rotaing Machinery
    Protective Capacitor-AC Rotaing Machinery

    25 kVAR to 1000 kVAR. 2,400 Volts to 25,000 Volts. 50 Hz and 60 Hz. Designed to meet IEC 871, IEEE 18 and CSA.

    View More
  • Single & Three Phase High Voltage Capacitors
    Single & Three Phase High Voltage Capacitors

    25 kVAR to 1000 kVAR. 2,400 Volts to 25,000 Volts. 50 Hz and 60 Hz. Designed to meet IEC 871, IEEE 18 and CSA.

    View More
  • Low Voltage Fixed Power Factor Capacitors
    Low Voltage Fixed Power Factor Capacitors

    240, 480, 600 volt ratings available 240V and 480V 3 phase units are Delta connected 600V units are Wye connected Not for use in harmonic conditions

    View More
  • Low Voltage Motor & Pump Power Factor Capacitors
    Low Voltage Motor & Pump Power Factor Capacitors

    240, 480 volt ratings available Outdoor weatherproof Three phase Delta, 60Hz

    View More
  • Medium Voltage Fixed Power Factor Capacitor Equipment
    Medium Voltage Fixed Power Factor Capacitor Equipment

    2400, 4160, 4800 volt ratings (higher voltage ratings available, contact factory) Indoor Dustrproof and Outdoor Weatherproof Three phase Delta, 60Hz Not for use in harmonic conditions

    View More
  • Medium Voltage Power Factor Capacitors
    Medium Voltage Power Factor Capacitors

    2400, 4160, 4800 volt ratings (higher voltage ratings available, contact factory) Indoor Dustrproof and Outdoor Weatherproof Three phase Delta, 60Hz Not for use in harmonic conditions

    View More
  • Induction Heating & Melting Capacitors Air and Water Cooled
    Induction Heating & Melting Capacitors Air and Water Cooled

    Air cooled and water cooled capacitors Single and multi-section designs 75 – 8300V 15Hz through 50khz

    View More
  • DC Power Electronic Capacitors
    DC Power Electronic Capacitors

    Commutation, Snubber and other high current electronic applications Up to 2000VDC Quick connect and threaded terminals

    View More
  • High Voltage Capacitor Fuses
    High Voltage Capacitor Fuses

    Fuse links and other high voltage fuse parts

    View More
  • GE B90 | Low Impedance Bus Differential System
    GE B90 | Low Impedance Bus Differential System

    Secure, dependable and scalable bus differential protection system for LV, HV and EHV busbars

    View More
  • GE B30 | Bus Differential System
    GE B30 | Bus Differential System

    Cost-effective, low-impedance, biased bus differential protection for up to six feeders The B30 features integrated protection, control and metering for MV, HV and EHV busbars, providing cost-effective, feature-focused busbar protection. Use the B30 to protect busbars with up to 6 feeders with up to two three-phase differential zones. The B30 is a cost-effective alternative to high-impedance schemes, ideal for breaker-and-half bus schemes, with integrated feeder backup protection and metering.

    View More
  • P346 Small Generator Protection with Differential
    P346 Small Generator Protection with Differential

    Advanced generator management relay with differential protection for small/medium generators Comprehensive generator and transformer protection and condition monitoring Support for a wide range of communication options including MODBUS, IEC60870-5-103, DNP 3.0 and IEC61850

    View More
  • P741 - Busbar Differential Relay (Central Unit)
    P741 - Busbar Differential Relay (Central Unit)

    Busbar scheme for centralized or distributed applications up to 8 zones + Check Zone and 28 bays. Adaptable to any busbar configuration. True sample based sub-cycle operation. Fully redundant communications between CU and PU’s. IEC 61850-9-2 LE process bus (with P743).

    View More
  • P747 – Busbar Differential Relay
    P747 – Busbar Differential Relay

    Complete protection for MV and HV Busbar configurations with up to 4 zones and 18 feeders Interoperable with all classes of CT: IEEE, IEC, air-gapped, non-gapped - and CTs with moderate knee point voltage 10 integrated function keys, tri-color LEDs, and graphical programmable logic permit the creation of comprehensive schemes, tailored to your needs IEC 61850 redundant Ethernet, supporting self-healing ring, RSTP, dual homing or PRP/HSR IEC62439 HSR compliant IEC61850 Ed 1

    View More
  • P742 - Busbar Differential Relay (Peripheral Unit)
    P742 - Busbar Differential Relay (Peripheral Unit)

    Peripheral Unit used with P741. 40TE case with standard IO. Backup protection functions (50 N&P/51 N&P/50ST P&N).

    View More
  • P746 – Busbar Differential Relay
    P746 – Busbar Differential Relay

    Complete protection for MV and HV Busbar configurations with up to 2 zones and 18 feeders Option of conventional VT or IEC 61850-9-2LE compliant sampled value Process Bus 10 integrated function keys, tri-color LEDs, and graphical programmable logic permit the creation of comprehensive schemes. IEC 61850 redundant Ethernet, supporting self-healing ring, RSTP, dual homing or PRP/HSR IEC62439 HSR compliant IEC61850 Ed 1

    View More
  • P743 - Busbar Differential Relay (Extended Peripheral Unit)
    P743 - Busbar Differential Relay (Extended Peripheral Unit)

    Peripheral Unit used with P741. IEC 61850 Ed.1 communication. IEC 61850-9-2 LE process bus ready. 60TE case with increased IO. Backup protection functions (50 N&P/51 N&P/50ST P&N).

    View More
  • MFAC: High – Speed Differential Protection Relay
    MFAC: High – Speed Differential Protection Relay

    MFAC 14 when only earth fault protection is required, MFAC 34 provides both phase and earth fault protection. Applications including generators, reactors, busbars, motors and the individual windings of power transformers. Ensuring high stability with through faults, with 'tuned to rated frequency' technique and a wide settings range Fast and reliable due to its simple electromechanical construction

    View More
  • MCAG High - Speed Differential Protection
    MCAG High - Speed Differential Protection

    Current-calibrated busbar differential relay highly-tuned to the fundamental to prevent spurious operation Attracted armature design with simple and robust construction High impedance protection principle High stability during through faults, Operation is fast and reliable (25ms at 5 x setting)

    View More
  • MVTP – Buswire Supervision Relay
    MVTP – Buswire Supervision Relay

    Single and 3-phase Models for continuous Buswire supervision Used in high impedance type Busbar protection schemes Detects open-circuited Buswire as well as open-circuited main current transformers. Integral Buswire shorting facility

    View More
  • GE D30 | Line Distance Protection System
    GE D30 | Line Distance Protection System

    Cost-effective, high-speed, primary and backup distance protection The D30 is a cost-effective distance protection system suitable for primary protection of sub-transmission lines and as a backup protection for HV, EHV lines, reactors and generators. The D30 provides five zones of phase and ground distance protection along with complete overcurrent and voltage protection functions intended for three-pole tripping applications. The D30 comes with versatile automation features using custom pilot schemes, which can be built.

    View More
  • GE L30 | Line Differential System
    GE L30 | Line Differential System

    The L30 is a cost-effective line current differential protection relay intended for sub-transmission and medium voltage lines and cables providing reliable and secure operation even under the worst case power system conditions. The L30 provides secure high-speed fault detection and clearance suitable for three-pole tripping applications. The L30 supports inter-relay communications via direct fiber as well as standard RS422, G.703 and C37.94 telecommunication interfaces. The L30 also provides synchrophasor measurements over Ethernet per IEEE C37.118.

    View More
  • GE D60 | Line Distance Protection System
    GE D60 | Line Distance Protection System

    High-speed transmission line protection with single/three-pole tripping The D60 is suitable for protecting transmission lines and cables including lines equipped with series compensation. The D60 supports dual-breaker applications and can be applied in single-pole or three-pole tripping applications. The D60 is applicable to different teleprotection schemes and includes inter-relay protection communications via direct fiber as well as different interfaces. The D60 also provides synchrophasor measurement over Ethernet per IEEE C37.118.

    View More
  • D90Plus | Line Distance Protection System
    D90Plus | Line Distance Protection System

    The D90Plus is a sub-cycle line distance protection system and bay controller suitable for protecting transmission lines and cables including lines equipped with series compensation. The D90Plus supports dual-breaker applications and can be used for single or three-pole tripping. The D90Plus supports different teleprotection schemes, including DCB, DCU, POTT, Hybrid POTT, and PUTT. The D90Plus also provides synchrophasor measurement over Ethernet per IEEE C37.118.

    View More
  • GE L90 | Complete Line Protection
    GE L90 | Complete Line Protection

    The L90 provides high-speed current differential protection suitable for transmission lines and cables of various voltage levels, while supporting complete distance protection and dual-breaker applications suitable for single and three-pole tripping applications. The L90 uses synchronized sampling at each relay to limit the impact of communications channel issues. The differential element's adaptive restraint balances sensitivity for internal faults and security during external faults. The L90 supports inter-relay protection communications via direct fiber as well as different interfaces.

    View More
  • GE L60 | Line Phase Comparison System
    GE L60 | Line Phase Comparison System

    The L60 provides fast and secure sub-cycle phase comparison protection, for both two-terminal and three- terminal lines, lines with series compensation and for single-pole and three-pole tripping applications. The L60 can operate using existing power line carrier or fiber optic communications, and compensates for channel asymmetry and charging currents. The L60 can provide complete support of dual-breaker line terminals by using multiple current inputs.

    View More
  • P543 Line Differential Protection (12” Case)
    P543 Line Differential Protection (12” Case)

    Line-Differential with Optional Subcycle Distance with 5 quadrilateral or mho zones and setting free power swing detection Advanced communications supporting IEC 61850 Ed.1 & Ed.2, redundant Ethernet, self-healing ring, RSTP, dual homing or PRP topologies Full suite of monitoring, control and recording capabilities plus fault locator, autoreclose and check synchronism

    View More
  • P544 Line Differential Protection (12” Case, 2 Breakers)
    P544 Line Differential Protection (12” Case, 2 Breakers)

    Line-Differential with Optional Subcycle Distance for 1 ½ Breaker Applications Advanced communications supporting IEC 61850 Ed.1 & Ed.2, redundant Ethernet, self-healing ring, RSTP, dual homing or PRP topologies Full suite of monitoring, control and recording capabilities plus fault locator, autoreclose and check synchronism

    View More
  • P545 Line Differential Protection (16” Case)
    P545 Line Differential Protection (16” Case)

    Line-Differential with Optional Subcycle Distance with 5 quadrilateral or mho zones and setting free power swing detection Advanced communications supporting IEC 61850 Ed.1 & Ed.2, redundant Ethernet, self-healing ring, RSTP, dual homing or PRP topologies Full suite of monitoring, control and recording capabilities plus fault locator, autoreclose and check synchronism

    View More
  • P546 Line Differential Protection (16” Case, 2 Breakers)
    P546 Line Differential Protection (16” Case, 2 Breakers)

    Line-Differential with Optional Subcycle Distance for 1 ½ Breaker Applications Advanced communications supporting IEC 61850 Ed.1 & Ed.2, redundant Ethernet, self-healing ring, RSTP, dual homing or PRP topologies Full suite of monitoring, control and recording capabilities plus fault locator, autoreclose and check synchronism

    View More
  • Common Equipment
    Common Equipment

    Lentronics Common Equipment including shelves, power, sync, CS service, orderwire and partyline units

    View More
  • Optical Level Interface
    Optical Level Interface

    Optical aggregate units

    View More
  • SPE Level Interface
    SPE Level Interface

    Ether-1000, DS3 and SPE units

    View More
  • VT Level Interface
    VT Level Interface

    T1/E1, Ether-10, JIF-Share and CDAX units

    View More
  • DS-0 Level Interface
    DS-0 Level Interface

    64kb/s channel units, including voice frequency, data and contact IO units

    View More
  • Teleprotection Interface
    Teleprotection Interface

    IEEE C37.94, 64k G.703, mirrored-bit RS232, direct transfer trip units

    View More
  • Cabling / Accessories
    Cabling / Accessories

    CBUS, JIF/TIF, CBW, Bypass, Optical cables and SFPs

    View More
  • Documentation
    Documentation

    Technical practice and installation manual (CD)

    View More
  • TUG-3 Level Interface
    TUG-3 Level Interface

    Ether-1000, TUG-3 Units

    View More
  • TU-1 Level Interface
    TU-1 Level Interface

    T1/E1, Ether-10, CMUX,Tie and CDAX Units

    View More
  • P14DA Directional Feeder Management Relay
    P14DA Directional Feeder Management Relay

    Directional feeder management relay for basic applications Compact withdrawable relay in a 20TE case size Up to 8 fully programmable opto inputs and 8 fully programmable output contacts

    View More
  • P145 Feeder Management Relay with Autoreclose, Synchronizing & Function Keys
    P145 Feeder Management Relay with Autoreclose, Synchronizing & Function Keys

    Feeder management system with Autoreclose, check synchronizing and function keys With 18 tri-color programmable LEDs Up to 32 opto inputs and 32 output contacts

    View More
  • GE F35 l Feeder Protection System
    GE F35 l Feeder Protection System

    Protection, control, monitoring and metering for multiple feeder applications. The F35, a member of the UR Family of protection relays, is the only feeder product on the market that provides feeder protection and power metering for up to five feeders with busbar voltage measurement, or six feeders without busbar voltage in one integrated package. Use the F35 as a stand-alone device or as a component of an automated substation control system.

    View More
  • GE F60 l Feeder Protection System
    GE F60 l Feeder Protection System

    Feeder protection, control, monitoring and metering in one integrated package. The F60, a member of the UR Family of protection relays, provides high performance feeder protection, control, monitoring and metering in an integrated, economical, and compact package. The F60 includes GE Multilin's unique high impedance fault detection for fast and reliable detection of faults caused by downed conductors.

    View More
  • GE 750/760 l Feeder Protection System
    GE 750/760 l Feeder Protection System

    Complete, economical protection and monitoring of industrial and utility feeders. The 750/760 Feeder Protection System, a member of the SR Family of protection relays, is a draw out digital relay intended for the management and primary protection of distribution feeders. It can also be used for management and backup protection of busses, transformers, and power lines.

    View More
  • GE F650 l Feeder Protection System
    GE F650 l Feeder Protection System

    High end features in an economical package. The F650, a member of the 650 Family of protection relays, is high performance digital device that incorporates protection, control, and metering in a economical package. Use the F650 to protect HV/MV feeders, bus couplers, transformers and capacitor banks. The F650 is the first feeder relay with remote I/O capabilities via the CIO module.

    View More
  • GE 350 l Feeder Protection System
    GE 350 l Feeder Protection System

    Innovative and intuitive multifunctional feeder relay offering protection, control and monitoring in one integrated, economical and compact package. Protection functions of this relay include over current and directional elements along with auto reclose and breaker failure. This 3 Series relay is available with draw out or non draw out options.

    View More
  • P14DB Directional Feeder Management Relay
    P14DB Directional Feeder Management Relay

    Directional Feeder Management relay available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Dedicated measured NVD input Pin-to-pin fast retrofit solution for selected legacy K-series relays (30TE case)

    View More
  • P144 Feeder Management Relay with Autoreclose & Transient Earth Fault Detection
    P144 Feeder Management Relay with Autoreclose & Transient Earth Fault Detection

    This product is under last-time buy. Orders may be placed until 31st December 2019, and will be fulfilled based upon availability. As an alternative, please refer to the P14D with Software 62. Feeder management system with novel transient earth fault detection algorithm for isolated/Petersen systems Dedicated measured NVD input (440Vac nominal input) Up to 16 opto inputs and 15 output contacts

    View More
  • P14DH Directional Feeder Management Relay with Wattmetric Directional Earth Fault
    P14DH Directional Feeder Management Relay with Wattmetric Directional Earth Fault

    Directional Feeder Management relay with wattmetric directional earth fault protection One single relay takes care of the PWH2 (wattmetric power) and PVH (neutral displacement voltage) functions. Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case IEC61850 communication protocol as an option

    View More
  • P143 Feeder Management Relay with Autoreclose & Check Synchronizing
    P143 Feeder Management Relay with Autoreclose & Check Synchronizing

    Feeder management system with Autoreclose and Check Synchronizing Modular 60TE or 80TE case size depending on ordering option Up to 48 opto inputs and 32 output contacts

    View More
  • P14DL Load / Line Management Relay
    P14DL Load / Line Management Relay

    Directional Advanced Feeder Management relay with autoreclose, check synchronizing and load management Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Powerful protection algorithms - neutral admittance protection, frequency supervised average rate of change of frequency and fault locator facilities

    View More
  • P142 Feeder Management Relay with Autoreclose
    P142 Feeder Management Relay with Autoreclose

    Feeder management relay with auto reclose Modular 40TE case size Up to 16 opto inputs and 15 output contacts

    View More
  • P14DZ Directional Feeder Management Relay with High Impedance Fault Detection/Transient Ground Fault Detection
    P14DZ Directional Feeder Management Relay with High Impedance Fault Detection/Transient Ground Fault Detection

    Directional Advanced Feeder Management relay with autoreclose, check synchronizing, load management and switchable HiZ fault detector or transient ground fault detection Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Pin-to-pin fast retrofit solution for legacy K-series relay models (30TE case)

    View More
  • P141 Feeder Management Relay
    P141 Feeder Management Relay

    Feeder management relay for main protection and backup of HV/EHV systems Modular 40TE case size Up to 8 opto inputs and 8 output contacts

    View More
  • P14NB Non-directional Feeder Management Relay
    P14NB Non-directional Feeder Management Relay

    Non-directional Feeder Management relay available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Pin-to-pin fast retrofit solution for selected legacy K-series relays (30TE case)

    View More
  • P153 Compact Feeder Protection Relay
    P153 Compact Feeder Protection Relay

    Non-directional overcurrent and earth fault protection for medium and low voltage applications Protection, measurement, monitoring and recording functions in one box User selectable communication protocols available

    View More
  • P14NZ Non-directional Feeder Management Relay with High Impedance Fault Detection
    P14NZ Non-directional Feeder Management Relay with High Impedance Fault Detection

    Non-directional Advanced Feeder Management relay with autoreclose and HiZ fault detector Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case

    View More
  • 735 to 850 Retrofit Kit
    735 to 850 Retrofit Kit

    Three-phase and ground feeder protection. Microprocessor-based draw out relay used to perform primary circuit protection on distribution networks at any voltage level.

    View More
  • P154 Non-directional Overcurrent Relay with Earth Fault
    P154 Non-directional Overcurrent Relay with Earth Fault

    Non-directional overcurrent and earthfault for MV/LV and HV backup feeder protection. Wide range of measurement, protection and monitoring functions to cover various applications Easy customization using programmable BI/BO/LEDs/AND logic etc.

    View More
  • P94VB Voltage and Frequency Relay
    P94VB Voltage and Frequency Relay

    Load Management relay with multiple stages of voltage and frequency protection Dedicated measured NVD input Available in either a 30TE or 40TE case TCS and Ethernet communications available together in 40TE case

    View More
  • P15D Dual Powered Overcurrent Relay
    P15D Dual Powered Overcurrent Relay

    Dual powered non directional overcurrent and earth fault relay Specially designed for RMU feeder applications where auxiliary supply is not available Measurement, protection and monitoring in one box

    View More
  • P94VP Voltage & Frequency Relay with Check Synch
    P94VP Voltage & Frequency Relay with Check Synch

    Advanced Load Management relay with check synchronizing Automatic load shedding and load restoration feature Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Retrofit solution for legacy KAVS relay (30TE case)

    View More
  • P94VR Voltage & Frequency Relay with Check Synch, Autoreclose
    P94VR Voltage & Frequency Relay with Check Synch, Autoreclose

    Advanced Load Management relay with check synch and autorelcose Available in either a 30TE or 40TE cases TCS and Ethernet communications available together in 40TE case Retrofit solution for KVTR and KAVR100 relay (30TE case)

    View More
  • Antennas
    Antennas

    GE MDS provides a full range of antennas to fit every specification and budget designed to have a long, trouble-free life.

    View More
  • RF Kits
    RF Kits

    The MDS RF Kits provide an easy-to-order wireless package. These kits include everything needed in typical applications, including wireless devices, antennas, cables, connectors, grounding, lightening arrestors, and power supplies.

    View More
  • Power Supplies
    Power Supplies

    Power supplies not only allow customers to increase the efficiency of their wireless system, but they can also help protect against power system overloads. MDS power supplies come with universal adapters and are available in a wide range to fit all MDS wireless devices

    View More
  • Installation Tools & Hardware
    Installation Tools & Hardware

    From stripping and deburring tools, to grounding and hanger kits, GE MDS offers a full compliment of professional installation tools to provide fast and easy installation of your communication system.

    View More
  • Filters & Surge Suppressors
    Filters & Surge Suppressors

    GE MDS provides many types of bandpass, band reject and notch filters with adjustable selectivity characteristics to allow a trade-off between insertion loss and selectivity.

    View More
  • ML3100 19
    ML3100 19

    The ML3100 is a modular layer 2 Ethernet switch with support for up to 8 ports GigE and 16 ports 10/100TX. The switch can be equipped with up to 16 ports Fiber. The switch is both IEEE 1588v2 and PoE capable.

    View More
  • ML3101 19
    ML3101 19

    The ML3101 is a modular layer 2 Ethernet switch with support for up to 8 ports GigE and 16 ports 10/100TX. The switch can be equipped with up to 16 ports Fiber. The switch is both IEEE 1588v2 and PoE capable and has field replaceable power supplies.

    View More
  • ML3000 19
    ML3000 19

    The ML3000 is a modular layer 2 Ethernet switch with support for up to 4 ports GigE and 32 ports 10/100TX. The switch can be equipped with up to 18 ports Fiber. The switch is both IEEE 1588v2 and PoE capable.

    View More
  • ML3001 19
    ML3001 19

    The ML3001 is a modular layer 2 Ethernet switch with support for up to 4 ports GigE and 32 ports 10/100TX. The switch can be equipped with up to 18 ports Fiber. The switch is both IEEE 1588v2 and PoE capable and has field replaceable power supplies.

    View More
  • ML1200 Compact Hardened Managed 12-port Ethernet Switch
    ML1200 Compact Hardened Managed 12-port Ethernet Switch

    The MultiLink ML1200 is compact and rugged, and suited for small to medium-sized deployments Configurations up to 12 ports, the ability to mix Fiber, Copper, and Gigabit connector types, and support for PoE

    View More
  • ML810 - Compact Hardened Managed 10-port Ethernet Switch
    ML810 - Compact Hardened Managed 10-port Ethernet Switch

    The MultiLink ML810 is a 10-port compact managed Ethernet switch that features cost-effective configurations and form factors in panel or DIN mounting options. Up to 8-ports PoE can reduce wiring costs for security applications.

    View More
  • MM300 | LV Motor Management System
    MM300 | LV Motor Management System

    The MM300 is a digital motor protection and control system, designed for Low Voltage motor applications. Flexible and powerful, the MM300’s protection

    View More
  • MM200 | LV Motor Management System
    MM200 | LV Motor Management System

    The MM200 is a digital motor protection and control system, designed for Low Voltage motor applications. Compact and powerful, the MM200’s protection can be scaled to the specific requirements of your system.

    View More
  • GE 469 | Motor Protection System
    GE 469 | Motor Protection System

    Complete, integrated protection and management of medium and large motors. The 469 Motor Protection System, a member of the SR Family of protection relays, is for protection and management of medium to large horsepower motors and driven equipment. It includes advanced features such as analog inputs for vibration monitoring, voltage dependent overload curves, torque protection & metering, and broken rotor bar protection. Use the 469 in two speed motors, motors with high inertia loads, or where reduced voltage starting is a requirement.

    View More
  • GE 369 | Motor Protection System
    GE 369 | Motor Protection System

    Comprehensive protection and monitoring for three-phase motors and their driven equipment. Designed for medium-sized motors, the enhanced 369 Motor Protection System delivers advanced motor health diagnostics, graphical and data rich fault diagnostics, simple six-step setup & configuration and complete traceability of setting changes, enabling industrial facilities to maximize process up-time and optimize rated motor output.

    View More
  • GE 339 | Motor Protection System
    GE 339 | Motor Protection System

    Complete protection, control, diagnostics and communications for small and medium sized AC motors. Designed for medium voltage motors in industrial applications, the 339 delivers unparalleled protection, control, diagnostics and communications in an industry leading draw-out construction. The 339 Motor Protection System provides simplified setup configuration through the use of the Motor Settings Auto-Configurator, advanced graphical diagnostics with the Motor Health Report and support for multiple communication protocols including IEC 61850. This 3 Series relay is available with draw out or non draw out options.

    View More
  • GE M60 | Motor Protection System
    GE M60 | Motor Protection System

    Comprehensive protection for medium and large motors. The M60, a member of the UR Family, is a full featured relay designed for the protection and management of medium and large horsepower motors. The M60 incorporates advanced features such as an enhanced thermal model, standard and custom thermal limit curves, current unbalance biasing, running and stopped exponential cooling curves, optional RTD modules, and hot/cold motor compensation. Use the M60 in protection applications requiring complex I/O configurations and high-speed communications.

    View More
  • GE MM2 | Motor Protection System
    GE MM2 | Motor Protection System

    Integrated process and electrical control with protection for low voltage motors. The Motor Manager 2 (MM2) combines control functions and comprehensive motor protection in one package. This compact device provides sophisticated control and protective relaying at significant cost savings. It includes integrated motor protection and process control in a small package, with or without display, that fits into standard MCC buckets.

    View More
  • GE 239 | Motor Protection System
    GE 239 | Motor Protection System

    Motor protection and management for small to medium size motors. The 239 Motor Protection relay is designed to provide protection and control to small to medium size motors. Use the 239 additional monitoring features to protect associated mechanical equipment from damage resulting from process malfunction.

    View More
  • GE SPM l Synchronous Motor Protection System
    GE SPM l Synchronous Motor Protection System

    The SPM controls starting, synchronizing, and protection of collector-ring or brushless type synchronous motors.

    View More
  • GE RMIO | Remote I/O Module
    GE RMIO | Remote I/O Module

    The Remote I/O Module provides RTD temperature metering capabilities for the Multilin 339 motor protection relay. The remote RTD Module provides additional protection for motor applications by monitoring the temperature of key components in the motor. All RTD’s settings are completely configurable via the 339 motor relay and via EnerVista Software.

    View More
  • P24NM Motor Protection with Current Inputs
    P24NM Motor Protection with Current Inputs

    Comprehensive motor protection functions for small and medium size industrial motors. Application flexibility with wide range of I/O and redundant Ethernet communications options in three different case sizes (20/30/40TE). Drawout design for simplified testing, commissioning and maintenance.

    View More
  • GE MM3 | Motor Protection System
    GE MM3 | Motor Protection System

    The Motor Manager 3 (MM3) combines control functions and comprehensive motor protection in one package. This compact device provides sophisticated control and protective relaying at significant cost savings over the discrete devices normally found in a low voltage motor control center (MCC).

    View More
  • RRTD | Remote RTD Module
    RRTD | Remote RTD Module

    The Remote RTD Module provides additional RTD temperature metering capabilities for other relays such as the 369.

    View More
  • GE 869 | Motor Protection System
    GE 869 | Motor Protection System

    The Multilin 869 relay is a member of the Multilin 8 Series protective relay platform and has been designed for the protection, control and management of medium and large induction and synchronous motors.

    View More
  • P241 Motor Protection Relay
    P241 Motor Protection Relay

    Advanced motor management relay Protection for both synchronous and induction motors Flexible communications supporting IEC6850 or DNP 3.0 Ethernet communications

    View More
  • P24DM Motor Protection with Current &Voltage Inputs
    P24DM Motor Protection with Current &Voltage Inputs

    Comprehensive motor protection functions for small and medium size industrial motors. Application flexibility with wide range of I/O and redundant Ethernet communications options in three different case sizes (20/30/40TE). Drawout design for simplified testing, commissioning and maintenance.

    View More
  • P242 Motor Protection with Extended IO
    P242 Motor Protection with Extended IO

    Advanced motor management relay with extended digital I/O Protection for both synchronous and induction motors Flexible communications supporting IEC6850 or DNP 3.0 Ethernet communications

    View More
  • P253 Motor Protection Relay
    P253 Motor Protection Relay

    Basic motor protection for small and medium size MV/LV motors Wide range of measurements for motor supervision and operations including starting current record Flexible SCADA communication options-Modbus/IEC60870-5-103 or DNP3.0

    View More
  • P243 Motor Protection Relay
    P243 Motor Protection Relay

    Advanced motor management relay with differential protection Protection for both synchronous and induction motors Flexible communications supporting IEC6850 or DNP 3.0 Ethernet communications

    View More
  • 269Plus to 369 Drawout Upgrade
    269Plus to 369 Drawout Upgrade

    Designed as a seamless upgrade for existing 269 Drawout relays. Utilizes existing 269 Drawout chassis, elimintating need to re-wire

    View More
  • GE C70 | Capacitor Bank Protection and Control System
    GE C70 | Capacitor Bank Protection and Control System

    The C70 is an integrated protection, control, and monitoring device for shunt capacitor banks based on the well established and proven UR relay platform of GE Multilin. The C70 provides both the bank and system protection schemes for shunt capacitor bank protection. The current and voltage-based protection functions provide sensitive protection for grounded, ungrounded single, and parallel capacitor banks and banks with taps.

    View More
  • GE C30 | Controller System
    GE C30 | Controller System

    The C30 controller system is a programmable logic controller for performing substation or bay automation that can also be used for expanding the I/O capability of protection devices and replacing Sequence of Event (SOE) recorders. The C30 provides fast deterministic execution of programmable logic with I/O capabilities far above an average protection relay.

    View More
  • GE C60 | Breaker Protection System
    GE C60 | Breaker Protection System

    The C60 breaker protection system is a substation hardened controller that provides a complete integrated package for the protection, control, and monitoring of circuit breakers. The C60 supports dual-breaker busbar configurations such as breaker-and-a-half or ring bus arrangements. Signals from up to 4 sets of CT’s can be brought into the C60 for internal summation.

    View More
  • GE N60 | Network Stability and Synchrophasor Measurement System
    GE N60 | Network Stability and Synchrophasor Measurement System

    The N60 network stability and synchrophasor measurement system is a flexible device intended for the development of load shedding, remedial action, special protection schemes and wide area monitoring and control. Like no one device before, the N60 shares real-time operational data to remote N60s so the system can generate intelligent decisions to maintain power system operation.

    View More
  • KITZ - Protocol Converter
    KITZ - Protocol Converter

    Communicate with any K-Bus device. Simple EIA232 connection. KITZ101 suitable for desktop use. ITZ102 suitable for rear of panel mounting. KITZ274 used in P741/2/3 Bus bar schemes.

    View More
  • GE DDFR | Distributed Digital Fault Recorder
    GE DDFR | Distributed Digital Fault Recorder

    The DDFR is a Digital Fault and Disturbance recording system that uses communications to retrieve Fault, Disturbance, and Sequence of Event records that are captured by the protection relays distributed throughout a substation. The DDFR internally stores this critical substation information for local station troubleshooting as well as archives this data in a remote enterprise network location for permanent storage and analysis.

    View More
  • GE CIO | Remote CAN I/O Module
    GE CIO | Remote CAN I/O Module

    The CAN bus Input/Output Module is a simple, robust device that provides additional input and output capabilities for GE Multilin's 650 family of relays. The CIO I/O capability can be doubled using a single CIO module with two boards. One CIO module, based on the ordering code, can handle as much as 32 inputs, 16 outputs, and 8 DC transducer inputs. Connects through optical fiber to F650 and future relays from the 650 Family. Reduce operating time, and simplify wiring for auxiliary inputs and outputs.

    View More
  • C650 Bay Control & Monitoring System
    C650 Bay Control & Monitoring System

    Advanced automation controller. High density, programmable I/O (up to 192 digital inputs and 48 digital outputs).

    View More
  • DR60 Digital Fault Recorder
    DR60 Digital Fault Recorder

    High accuracy fault & disturbance recording capturing 512 samples / cycle High density inputs / outputs (Up to 16 VT + 16 CT inputs, 96 binary inputs, 32 transducer inputs & 48 binary outputs) Advanced communications including support for IEC 61850 and time synchronization with IEEE 1588 v2

    View More
  • RPV311 Multifunction Recorder
    RPV311 Multifunction Recorder

    Distributed Multifunction Recorder designed for conventional and digital substations Optional Travelling Wave Fault Locator for extremely precise fault location Features Phasor Measurement Unit according to C37.118-2014a Exclusive Waveform Measurement Unit function for very fast synchrophasor streaming and detection of sub-synchronous oscillations in conjunction with e terraphasorpoint Supports GOOSE and Sampled Measured Values acquisition (according to IEC 61850-9-2LE)

    View More
  • RA331 Acquisition Module for RPV311
    RA331 Acquisition Module for RPV311

    Acquisition unit for GE Reason RPV311 multifunction recorder Multimode ST fiber for connection to a processing unit up to 2km apart Up to 8 analog inputs field selectable for voltage or current Up to 32 binary inputs

    View More
  • RA332 Acquisition Module for RPV311
    RA332 Acquisition Module for RPV311

    Acquisition unit for GE Reason RPV311 multifunction recorder Multimode ST fiber for connection to a processing unit up to 2km apart Up to 16 analog inputs field selectable for voltage or current Up to 32 binary inputs

    View More
  • RA333 Travelling Wave and DFR Acquisition Module for RPV311
    RA333 Travelling Wave and DFR Acquisition Module for RPV311

    Acquisition unit for GE Reason RPV311 multifunction recorder Multimode ST fiber for connection to a processing unit up to 2km apart 3 ultra-fast voltage channels for Travelling Wave acquisition Up to 8 analog inputs field selectable for voltage or current Up to 32 binary inputs

    View More
  • HardFiber Brick Process Interface Unit
    HardFiber Brick Process Interface Unit

    The HardFiber Brick is a simple interface providing four bi-directions point-to-point connections to protection and control devices. Featuring a rugged die-cast aluminum housing is rated IP66, from -40 to 85C, and 30g shock. Available in standard kiosk case S-Brick and ruggedized case for outdoor Brick mounting.

    View More
  • IEC 61850 Process Bus Module
    IEC 61850 Process Bus Module

    The Multilin HardFiber Process Bus module for the Universal Relay (UR) family of protection and control products implements the HardFiber IEC 61850 Process Bus system.

    View More
  • MU320 Integrated Merging Unit
    MU320 Integrated Merging Unit

    MU320 is a stand-alone analog Merging Unit able to monitor up to two bays or up to 16 analog inputs Samples Measurement Values in accordance to IEC 61850-9-2LE attested by TÜV SÜD and supporting both Protection (80 s/c) and Measurement (256 s/c) profiles Implements mode/behaviors according to IEC 61850 Ed. 2, including test mode, and supports MMS Report control block for easier integration with supervisory systems

    View More
  • D20/D200 Substation Controller
    D20/D200 Substation Controller

    The iBox Controller is a compact, substation hardened, pole-top or pad-mounted control device Featuring a large protocol library to facilitate communications to most existing substation devices

    View More
  • P30 Phasor Data Concentrator
    P30 Phasor Data Concentrator

    Collects, aggregates and archives synchrophasor time aligned data within the Substation for enhanced post event analysis Continuously records and reports synchrophasor data through up to eight C37.118 clients for wide area monitoring applications

    View More
  • EnerVista | Device setup and document management toolset
    EnerVista | Device setup and document management toolset

    EnerVista™ is an industry-leading suite of software tools designed to simplify every aspect of working with GE Multilin and other field devices. Our modular suite of software tools significantly reduces effort and streamlines operations such as creating and validating settings files; integrating GE Multilin devices with Automation systems; and monitoring and controlling devices to protect end assets.

    View More
  • EnerVistaTM Viewpoint Monitoring ViewNodes
    EnerVistaTM Viewpoint Monitoring ViewNodes

    The EnerVista ViewNode software allows multiple users to remotely monitor and control existing Viewpoint Monitoring systems. Multiple user accounts and security levels ensures system information is always accessible and secure.

    View More
  • Software
    Software

    VistaNET premium components including SNMP, traffic, server, comm. Port expansion licenses

    View More
  • Services
    Services

    Hands-on and topic-specific training

    View More
  • EPM 7000T Power Quality Meter with No Display
    EPM 7000T Power Quality Meter with No Display

    EPM 7000 Power Meter without display, DIN mount 0.2% Watt-Hour Accuracy and waveform capture at up to 512 samples/cycle Up to 4MB of data logging Field Replaceable I/O modules

    View More
  • EPM 9900P Advanced Power Quality Meter
    EPM 9900P Advanced Power Quality Meter

    0.06% Energy accuracy (ANSI 0.2%). Harmonics to the 511th order (Voltage, Current) with up to 4GB data logging. Advanced communications including IEC 61850 high speed GOOSE messaging.

    View More
  • EPM 9700 Advanced Power Quality Meter
    EPM 9700 Advanced Power Quality Meter

    IEC 61000-4-30 Class A Ed.3 Power Quality Meter with EN50160 support. Up to 1.2 GB of logging memory with default preconfigured logging of 142 essential parameters. 6 standard communications ports including 4 serial and 2 Ethernet ports.

    View More
  • GE EPM 9800 | Advanced Power Quality Metering System
    GE EPM 9800 | Advanced Power Quality Metering System

    Precision Measurement, Advanced Communication, Basic PQ and Alarm Reporting, Economical Recording Meter. The socket type mount design EPM 9800 meter is perfect for industrial and utility substation automation applications where both power quality monitoring and revenue accuracy are required.

    View More
  • GE EPM 9650 | Advanced Power Quality Metering System
    GE EPM 9650 | Advanced Power Quality Metering System

    High Performance Power Meter and Data Acquisition Node. Perfect for industrial, commercial and utility applications, among the advanced features the EPM 9650 supports are Transformer Loss Compensation, onboard time of use and high speed waveform capture. The EPM 9650 includes increased memory capacity for data logging, and optional EN50160 Flicker and compliance monitoring.

    View More
  • GE EPM 9450 | Advanced Power Quality Metering System
    GE EPM 9450 | Advanced Power Quality Metering System

    High Performance Power Meter and Data Acquisition Node. Perfect for industrial, commercial and utility applications, among the advanced features the EPM 9450 supports are Transformer Loss Compensation, onboard time of use and high speed waveform capture. Meter includes all the attributes required for highest level of PQ analysis and communication.

    View More
  • GE EPM 7000 | Power Quality Meter
    GE EPM 7000 | Power Quality Meter

    The EPM 7000 meter provides revenue class (0.2%) three phase power metering with optional Ethernet, relay, status, and analog output communication modules. This flexible meter can be used for a wide range of high accuracy applications including disturbance recording and power quality studies.

    View More
  • GE PQM II | Power Quality Metering System
    GE PQM II | Power Quality Metering System

    Continuous Metering of three-phase systems with waveform and data logging. The PQM II is a digital metering device that provides continuous monitoring of a three-phase system. It provides metering of current, voltage, real and reactive power, energy use, cost of power, power factor and frequency.

    View More
  • GE EPM 6010 | Building Automation Power Meter
    GE EPM 6010 | Building Automation Power Meter

    The Multilin EPM 6010 is a revenue grade power meter with native BACnet/IP communications. This meter is designed to integrate seamlessly into existing and new building management systems using the popular BACnet protocol. The meter allows users to gather data on voltage, current, power and energy usage throughout a facility.

    View More
  • GE EPM 2200 | Power Metering System
    GE EPM 2200 | Power Metering System

    The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. The meter is very easy to configure, read and installs into standard 92mm DIN and ANSI C39.1 Round Cut-outs

    View More
  • GE EPM 2000 | Power Metering System
    GE EPM 2000 | Power Metering System

    Full Featured Metering with Advanced Power Measurement. The EPM 2000 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications.

    View More
  • GE EPM 4600 | Multi-Feed Power and Energy Metering Solution
    GE EPM 4600 | Multi-Feed Power and Energy Metering Solution

    The Multilin EPM 4600 Multi-feed Power and Energy Meter is a submetering solution that allows owners and operators to quickly, accurately and centrally measure power and energy usage of specific areas to reduce operating expenses. The EPM 4600 provides comprehensive data logging and trending capabilities and includes a broad range of communication options including Wi-Fi, Ethernet RS485 or USB for easy integration in both existing or new infrastructures.

    View More
  • GE EPM 6100 | Energy Submeter with WiFi
    GE EPM 6100 | Energy Submeter with WiFi

    The EPM 6100 is a powerful tool for monitoring and managing energy usage within factories, businesses and across campuses. EPM 6100 features 0.2% accuracy, as well as RS485, RJ45 Ethernet or WiFi communications. Early detection of power problems is facilitated through THD and the alarming capabilities of the EPM 6100.

    View More
  • GE EPM 6000 | Power Meter
    GE EPM 6000 | Power Meter

    EPM 6000 is one of the industry’s highest performance revenue grade panel meters. Based on the latest technology and an all-new platform, EPM 6000 has a superior cost to performance ratio and significantly outperforms other metering products many times its price.

    View More
  • GE EPM 7100 | Power Quality Meter
    GE EPM 7100 | Power Quality Meter

    The EPM 7100 is a powerful tool that allows customers to monitor and manage their energy usage within factories, businesses and across campuses. The EPM 7100 is a multifunction meter that features ANSI C12.20 (0.2% class) accuracy and RS485, RJ45 Ethernet or IEEE 802.11 WiFi communication connections, making the meter easy to deploy in modern and older communications systems.

    View More
  • EPM 6010T Building Automation Power Meter, No Display
    EPM 6010T Building Automation Power Meter, No Display

    EPM 6010 Power Meter without display, DIN mount BACnet/IP Protocol 40 BACnet Objects Embedded HTTP Server 0.2% Watt-Hour Accuracy

    View More
  • EPM 6000T Multi-Function Power Meter with No Display
    EPM 6000T Multi-Function Power Meter with No Display

    EPM 6000 Power Meter without display, DIN mount Multifunction Power and Energy Meter 0.2% Watt-hour accuracy Ethernet communications

    View More
  • EPM 4600 Touch Screen Display
    EPM 4600 Touch Screen Display

    Energy and metering information readily available for viewing User-friendly, touch screen, color LED display available in both 3.5" and 5.7" sizes Comes pre-configured or can be easily customized

    View More
  • Communicator Meter Setup & Data Acquisition Software
    Communicator Meter Setup & Data Acquisition Software

    Advanced, intuitive software for meter configuration and monitoring View & analyze real-time meter data Powerful graphical charting and power quality analysis tools

    View More
  • Energy Aggregator - Energy Visualization/Reporting Software
    Energy Aggregator - Energy Visualization/Reporting Software

    Complete, cost effective visualization, reporting and billing solution. Automatically collect and centralize data from logging GE’s EPM Meters. Measure and action energy management goals.

    View More
  • M355 Class A Power Quality Analyser
    M355 Class A Power Quality Analyser

    Class 0.2S Energy Measurement Accuracy IEC 61000-4-30 Class A Power Quality Meter with EN50160 Reporting 8MB Logging Memory with expandable memory card Modbus and DNP3 Communications

    View More
  • I500 Single Phase High Performance Transducer
    I500 Single Phase High Performance Transducer

    Multifunction Single Phase Transducer (Current, Voltage/Frequency or Power) 0.2% Accuracy MODBUS over Serial (RS232/RS485), USB or Ethernet communications Multifunction Transducer with optional data log

    View More
  • I500 Three Phase High Performance Multifunction Transducer
    I500 Three Phase High Performance Multifunction Transducer

    Multifunction Transducer with optional data log Dedicated Power Quality model 0.2% Accuracy, 120 measured and calculated values MODBUS over Serial (RS232/RS485), USB or Ethernet communications 4 ports for analog and digital IO options Port for optional remote display (I5R)

    View More
  • I500 Remote Display
    I500 Remote Display

    Remote LCD Display for I500 Transducers programming and Viewing of I500 Connect to 31 I500 Transducer

    View More
  • BA300 Substation Battery Monitoring
    BA300 Substation Battery Monitoring

    Monitors critical DC operated systems Ensures battery charger is operating correctly Alarms when battery circuit impedance exceeds safe operating levels

    View More
  • ISTAT M2x3 High Performance Measurement Centre
    ISTAT M2x3 High Performance Measurement Centre

    M2X3 family of economic, high accuracy meters, logging and analyser applications. Multiple Input/Output options, serial and Ethernet communications. Easily configurable, with multi line display, wrong connection warning and set up wizard. M253 Power Quality compliance to EN50160.

    View More
  • I400 I4 Mean Sensing Transducers
    I400 I4 Mean Sensing Transducers

    Models: I4CA Current and I4VA Voltage Transducers Self Powered Single Analogue Output Compact design

    View More
  • I4D DC Transducers
    I4D DC Transducers

    Comprehensive range of DC measurements: I4DA Tap Position Indication, I4DB Voltage, I4DC Current, IDF Resistance and I4DG Temperature Optional Universal AC/DC supply (40-276 Vac, 24-300 Vdc) Optional RS232 or RS485 MODBUS Communications Port DIN Rail Mounting

    View More
  • I400 I4M RMS Transducers
    I400 I4M RMS Transducers

    Models: I4MC Current and I4MV Voltage Transducers Universal Ac/Dc Auxiliary Supply Single Analogue Output Compact design

    View More
  • ISTAT M2x2 Measurement Centre
    ISTAT M2x2 Measurement Centre

    Models: M212 non communicating and M232 with Modbus Communications Energy Class 1, 0.5% Accuracy Auto-ranging secondary voltage and current setting Universal Ac/Dc Auxiliary Supply Easily configurable, with multi line display, wrong connection warning and set up wizard.

    View More
  • MultiNet1000 Hardened Router
    MultiNet1000 Hardened Router

    The MultiNet 1000 Managed Router is an industrial-hardened, multipurpose networking appliance that combines a serial port server, a managed switch, and a full-featured WAN & Ethernet Router into a single device.

    View More
  • MC-E10 Ethernet to 10Mbps Fiber Converter
    MC-E10 Ethernet to 10Mbps Fiber Converter

    This product is under last-time buy. Orders may be placed until 17th April 2020, and will be fulfilled based upon availability.Please contact us to discuss alternatives. The MC-E10 is a 10/100 Ethernet to 10Mbps fiber media converter designed and built for use in harsh industrial and utility environments.

    View More
  • MC-E100 Ethernet to 100Mbps Fiber Converter
    MC-E100 Ethernet to 100Mbps Fiber Converter

    This product is under last-time buy. Orders may be placed until 17th April 2020, and will be fulfilled based upon availability.Please contact us to discuss alternatives. The MC-E100 is a 10/100 Ethernet to 100Mbps fiber media converter designed and built for use in harsh industrial and utility environments.

    View More
  • MC-E1000 Ethernet to 1000Mbps Fiber Converter
    MC-E1000 Ethernet to 1000Mbps Fiber Converter

    This product is under last-time buy. Orders may be placed until 17th April 2020, and will be fulfilled based upon availability.Please contact us to discuss alternatives. The MC-E1000 is a 10/100/1000 Ethernet to 1000Mbps fiber media converter designed and built for use in harsh industrial and utility environments.

    View More
  • DAP-416 Multi-function Substation Server
    DAP-416 Multi-function Substation Server

    Substation server for the management, security and delivery of substation information to substation operators Ruggedized and modular hardware for power substation environments

    View More
  • DAP-AT Multi-function Substation Server
    DAP-AT Multi-function Substation Server

    Multi-function server to manage, secure and deliver substation information to grid operators Optimize performance critical substation assets

    View More
  • GE D20MX | Substation Controller
    GE D20MX | Substation Controller

    Simple to Advanced Substation Automation Control

    View More
  • GE D20 RIO | Distributed I/O Controller
    GE D20 RIO | Distributed I/O Controller

    GE's Multilin D20 RIO is a stand-alone, small form factor device designed to provide distributed I/O capabilities for easy connection to the Multilin D400™ gateway through any point in the substation LAN.

    View More
  • G500 Substation Gateway
    G500 Substation Gateway

    Offers a high-capacity, secure, substation-hardened set of modular and expandable hardware and software components to simplify deployment, operation and maintenance of automation systems Designed to provide a reliable and accurate collection of data (metering, status, events and faults) from substation devices to SCADA, EMS, DMS or other enterprise applications

    View More
  • D400 Substation Gateway
    D400 Substation Gateway

    GE's D400 substation data manager is a secure, substation-hardened gateway Features the collection of metering, status, event, and fault report data from serial or LAN based devices.

    View More
  • D20E Substation I/O Module
    D20E Substation I/O Module

    The next-generation input/output (I/O) module for substation automation and SCADA RTU applications A practical and cost-effective solution for D20 I/O and RTU upgrades

    View More
  • GE KELMAN TransportX
    GE KELMAN TransportX

    Compact portable system that performs laboratory quality Dissolved Gas Analysis on manually taken transformer oil samples and renders a diagnostic on-site in 30 minutes.

    View More
  • GE Intellix BMT300   | Bushing Tan Delta and Partial Discharge Monitoring
    GE Intellix BMT300 | Bushing Tan Delta and Partial Discharge Monitoring

    GE's Intellix BMT 300 is an intelligent, on-line system that continuously monitors not only the condition of transformer bushings but also the presence of Partial Discharge (PD) activity in the main tank. It will alert personnel of fault conditions at an early stage and provide vital health information on the bushings and the transformer.

    View More
  • GE Perception Fleet
    GE Perception Fleet

    GE’s Perception Fleet is a smart, simplified and standards-based software system that moves customers from a manual, one-on-one transformer assessment process to an automated and online fleet management assessment. By automatically evaluating the condition of assets and establishing their risk of failure, Perception Fleet is able to prioritize and rank assets within a fleet. The Perception Fleet software provides customers comprehensive transformer fleet condition rankings, transformer risk information, and expert analysis on-demand, removing time-consuming and costly manual processes as well as unnecessary maintenance, helping focus capital and reduce operational expenses.

    View More
  • GE Intellix MO150
    GE Intellix MO150

    Intelligent transformer monitoring system designed to collect real-time data obtained from an array of sensors and deliver information based on the results of IEEE/IEC standards transformer mathematical models.

    View More
  • Kelman DGA 900
    Kelman DGA 900

    9-gas & moisture online transformer DGA. Features innovative two enclosure design for flexible installation, local/remote HMI and expandable analogue/digital I/Os New Rapid Mode – provides near real time insight on fast developing faults about 30 minutes

    View More
  • EPM 2000 | Power Metering System
    EPM 2000 | Power Metering System

    The EPM 2000 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2000 can easily be mounted in a panel for generator monitoring, substation automation and more. Meter can also provide data to RTUs, PLCs and other control devices.

    View More
  • EPM 2200 | Power Metering System
    EPM 2200 | Power Metering System

    The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.

    View More
  • EPM 6000 | Multifunction Power Metering System
    EPM 6000 | Multifunction Power Metering System

    EPM 6000 is one of the industry’s highest performance revenue grade panel meters. Based on the latest technology and an all-new platform, EPM 6000 has a superior cost to performance ratio and significantly outperforms other metering products many times its price.

    View More
  • EPM 6100 | Energy Submeter with WiFi
    EPM 6100 | Energy Submeter with WiFi

    The EPM 6100 is a powerful tool that allows customers to monitor and manage their energy usage within factories, businesses and across campuses. The EPM 6100 is a multifunction meter that features ANSI C12.20 (0.2% class) accuracy and RS485, RJ45 Ethernet or IEEE 802.11 WiFi communication connections, making the meter easy to deploy in modern and older communications systems. Early detection of power problems is facilitated through THD and the alarming capabilities of the EPM 6100. The units use standard 5 or 1 amp CTs (either split or donut), surface mount to any wall and are easily programmed in minutes.

    View More
  • EPM 7100 | Energy Submeter with Data Logging and WiFi
    EPM 7100 | Energy Submeter with Data Logging and WiFi

    The EPM 7100 is a powerful tool that allows customers to monitor and manage their energy usage within factories, businesses and across campuses. The EPM 7100 is a multifunction meter that features ANSI C12.20 (0.2% class) accuracy and RS485, RJ45 Ethernet or IEEE 802.11 WiFi communication connections, making the meter easy to deploy in modern and older communications systems. The extensive data logging and alarm recording capabilities of the EPM 7100 enable advanced analysis and predictive maintenance of the power system. The units use standard 5 or 1 amp CTs (either split or donut), surface mount to any wall and are easily programmed in minutes.

    View More
  • EPM 6010 | Building Automation Power Meter
    EPM 6010 | Building Automation Power Meter

    The Multilin EPM 6010 is an industry leading revenue grade power meter with native BACnet/IP communications. This meter is designed to integrate seamlessly into existing and new building management systems using the popular BACnet protocol. The meter allows users to gather data on voltage, current, power and energy usage throughout a facility. This meter is available in a transducer configuration (EPM 6010T) that comes without a display and has a DIN rail mount. It’s ideal for use in retrofit applications and where budgets are a large consideration.

    View More
  • EPM 4600 | Multi-Feed Power and Energy Metering Solution
    EPM 4600 | Multi-Feed Power and Energy Metering Solution

    To support and implement an effective energy management strategy, a baseline of energy measurements are required. The Multilin EPM 4600 Multi-feed Power and Energy Meter is a sub-metering solution that allows owners and operators to quickly, accurately and centrally measure power and energy usage of specific areas to reduce operating expenses. The EPM 4600 empowers users with greater energy awareness leading to improved tenant attraction and retention and greater overall energy efficiency throughout facilities.

    View More
  • M-Pact Series
    M-Pact Series

    Rated from 800 to 4000A the M-PACT circuit breaker has been designed to meet the most stringent demands in fault detection and safe interruption thereof.

    View More
  • Entelliguard Series
    Entelliguard Series

    EntelliGuard G circuit breakers are the newest line of GE low-voltage circuit breakers, the next step in the evolution of a line known for its exceptional reliability and performance.

    View More
  • Recorded Plus Series
    Recorded Plus Series

    The Record PlusTM family of circuit breakers has been developed as a line of aesthetically and technically coordinated protection devices for low voltage distribution and control applications. The circuit breakers are available in four sizes, each of which is tailored to the individual requirements associated with its application.

    View More
  • Redline Series
    Redline Series

    Miniature Circuit Breakers (MCB) are intended for theprotection of wiring installations against both overloadsand short-circuits in domestic or commercial wiringinstallations where operation is possible by uninstructed people.

    View More
  • DMS - LINE
    DMS - LINE

    MCB's, RCCB's / RCBO's for domestic installations

    View More
  • Contactor
    Contactor

    Three and four pole contactors 9 to 105A (AC3) 25 to 140A (AC1) And 150 to 825A (AC3) 200 to 1250A (AC1)...

    View More
  • Thermal Overload Relay
    Thermal Overload Relay

    Thermal overload relays for contactors from 0.16 to 850A - Control circuit up to 690V AC, Power circuit...

    View More
  • Manual Motor Starter
    Manual Motor Starter

    Rocker and rotary handle operator Thermal and magnetic protection, Standard and high breaking capacity...

    View More
  • EPM 7000 | Power Quality Meter
    EPM 7000 | Power Quality Meter

    The EPM 7000 provides continuous metering of three-phase systems with waveform and data logging. It performs energy measurements with 0.2% accuracy and supports optional Ethernet, relay, status, and analog output communication modules. This flexible meter can be used for a wide range of high accuracy applications including disturbance recording and power quality studies. This meter is available in a transducer configuration (EPM 7000T) that comes without a display and has a DIN rail mount. It’s ideal for use in retrofit applications and where budgets are a large consideration.

    View More
  • EPM 9000/9450/9650 | Advanced Power Quality Metering System
    EPM 9000/9450/9650 | Advanced Power Quality Metering System

    The EPM 9450/ 9650 is the entry point for GE's premium 9000 meter series with advanced power quality capability. The unit utilizes ACCU-Measure® Technology to provide highly accurate revenue grade readings coupled with advanced data analysis. The unit measures over 15,000 electrical parameters including real time harmonics to the 127th order, voltage surges and sags and a large assortment of advanced monitoring functionality. The unit also provides advanced expandable I/O with up to 256 points for control, data acquisition and alarms functions.

    View More
  • EPM 9800 | Advanced Power Quality Metering System
    EPM 9800 | Advanced Power Quality Metering System

    With the socket type mount design EPM 9800 meter is perfect for industrial and utility substation automation applications where both power quality monitoring and revenue accuracy are required. EPM 9800 provides most accurate analysis of electric power and energy. Using advanced DSP technology meter measures instant and stored revenue power data. Meter includes all the attributes required for highest level of PQ analysis and communication. From today's utility giants to large industrial users to local electrical municipal, an effective energy management and power-monitoring program is critical for success. The EPM 9800 is an advanced monitoring product, providing the total picture of power usage and power quality for any metered point within a power distribution network allowing users to make power related decisions quickly and effectively. With its web server capability, EPM 9800 can be monitored anytime and from anywhere via the Internet. EPM 9800 is simple to use and easy to set up.

    View More
  • EPM 9900 | Advanced Power Quality Metering System with Transient Recorder
    EPM 9900 | Advanced Power Quality Metering System with Transient Recorder

    The EPM 9900 is one of the most advanced monitoring products on the market today, providing you with the total picture of energy usage and power quality from any metered point in a power distribution network. This allows you to make power related decisions quickly and effectively.

    View More